Browse all practice questions for the Safety for Electricians Module 2 Practice Test. Search by topic, open any question and review its full explanation, then test yourself in the practice quiz.

Safety for Electricians Module 2 Practice Test course image
More practice questions

These questions are part of the practice quiz. Start practicing

  • CFR Part 1926 covers which OSHA standards?
  • Distinguish between the limited approach boundary and the restricted approach boundary.
  • In the event of electrical fibrillation, who should operate the defibrillator?
  • Which statement accurately describes how arc flash PPE is selected?
  • Which documents govern electrical safety in the workplace for electricians in many jurisdictions?
  • Which class has the highest voltage rating and what is that rating?
  • How should insulating gloves be tested and cared for before use?
  • What steps should be followed to verify that a circuit is de-energized before starting work?
  • If a person's heart begins to fibrillate due to an electrical shock, the recommended action is to have a qualified person use a defibrillator.
  • Which item is NOT required on an arc flash label?
  • Which items are typically included in electrical safety training?
  • What is the proper distance from ladder feet to the wall?
  • What does the arc flash boundary indicate?
  • What is the life-threatening condition called when heart muscle fibers contract irregularly?
  • Which of the following best describes the documentation produced during hazard analysis?
  • How does GFCI protection differ from equipment grounding?
  • Which item is part of an effective post-work verification after electrical work?
  • A first-year electrical apprentice is most likely to be which of the following?
  • What should be included on an arc flash label for equipment?
  • A potential contaminant found in certain fluorescent fixtures is:
  • A double-insulated power tool can be used in place of what?
  • What safety measures should be in place when working on overhead or exposed conductors in outdoor environments?
  • Which class of gloves is used for voltages up to 1,000 volts?
  • The elevation threshold for fall protection is ____.
  • What actions should be taken if PPE is damaged or failed during work?
  • Polychlorinated biphenyls (PCBs) are chemicals that may be found in large transformers and capacitors. What term describes these chemicals?
  • What is the primary purpose of a permit for energized work?
  • What safety step is essential when replacing a fuse or breaker?
  • Scheduling off-shift maintenance work is an example of which type of control?
  • The arc rating indicates the garment's resistance to which type of energy in arc flash scenarios?
  • Differentiate shock hazard from arc flash hazard in electrical work.
  • Which PPE item is a key component of arc flash protection?
  • The NFPA 70E standard covers the ____.
  • Which three elements must be included in a Lockout/Tagout procedure?
  • Which program elements are essential for continuous safety improvement?
  • Which CFR part number governs OSHA standards for General Industry?
  • Who is considered a 'Qualified Person' under NFPA 70E?
  • Which statement best describes an engineering control?
  • CFR Part 1910 covers which OSHA standards?
  • Which statement best describes the relationship between incident energy and PPE category?
  • Which elements define a 'clear work area' around electrical equipment?
  • What signs of insulation deterioration can megger testing reveal?
  • Which statement accurately summarizes the relationship between preventative and corrective maintenance?
  • Which CFR part governs OSHA standards for the Construction Industry?
  • When is it appropriate to remove a lockout device or tag?
  • As it is erected, each part of a scaffolding shall be carefully ____.
  • What constitutes complete safety documentation and why is it important?
  • Which of the following is true regarding hand tools?
  • What is arc flash hazard analysis and its key outputs?
  • At an elevation of 7 feet, is fall protection required?
  • The OSHA lockout/tagout rule ______.
  • The type of hard hat that can withstand a voltage of 20,000 VAC for three minutes is a which class?
  • What does the two-person rule provide in terms of rescue readiness and supervision?
  • Fall protection requirements apply starting at elevations of how many meters?
  • Which statement is true about NFPA 70E?
  • If you are performing work at 1.9 meters, is fall protection required?
  • A work permit is a type of which control?
  • Which action is part of testing performed after installation or repair?
  • Which height corresponds to the 1.8 meter threshold in feet?
  • Which boundary is the approach limit at which a shock hazard exists?
  • How often should electrical PPE be inspected?
  • When moving a sharp hand tool from one location to another, you should keep the blade pointing away from your body.
  • What is the primary goal of preventative maintenance in electrical safety?
  • Maintaining three-point contact on a ladder requires having three points of contact at all times.
  • Which information must be included on an arc flash label?
  • Tools made of nonconductive material and insulated from electrical energy are called?
  • How should you respond to an electrical shock if you’re trained?
  • A work permit illustrates which category of risk control?
  • What is the difference between electrical safety training and job-specific electrical safety procedures?
  • Which statement best describes verification of de-energization in a lockout/tagout program?
  • At what height above a lower level is fall protection required on surfaces with unprotected edges?
  • A garment's arc rating is its maximum incident energy resistance demonstrated prior to material breakdown, or at the onset of a second-degree skin burn. What term describes this property?
  • Which statement best describes lockout versus tagout in a LOTO program?
  • What does SDS stand for in safety documentation?
  • What happens to the permits used to enter a confined space?
  • Fall protection is required when working at elevations of _____.
  • Which color tag corresponds to Class 0 protective equipment?
  • Which item is NOT typically considered one of the most life-threatening hazards on a construction site?
  • All conductors, buses, and connections should be considered ____ until proven otherwise.
  • When evaluating safety on a job site, which compound might you encounter in some fluorescent fixtures?
  • What are touch potential and step potential, and why are they hazards near outdoor high-voltage sources?
  • Minimum Approach Distance means:
  • What is the key benefit of a pre-task briefing in electrical work?
  • What is the definition of preventative maintenance in the context of electrical safety?
  • What are the key PPE components for arc flash protection and what determines their use?
  • Grounding integrity checking is intended to ensure what?
  • The maximum scaffold plank overhang beyond end support is measured in which unit?
  • Where should energized equipment or lockout devices during maintenance?
  • Fluorescent fixtures may contain PCBs. Choose the correct option.
  • Which statement best differentiates lockout from tagout?
  • A device that will de-energize a circuit if the current to ground exceeds a predetermined value is a?
  • Which boundary is defined as the approach limit at a distance from an exposed energized conductor where there is an increased likelihood of electric shock?
  • What is the primary purpose of NFPA 70E in electrical safety for workers?
  • When testing instruments used on live circuits, which statement is correct?
  • Ladder safety guidelines indicate the distance from feet to wall should be what fraction of the ladder’s working height?
  • What is the unit used to measure incident energy in arc flash calculations?
  • Which boundary is defined as the distance from exposed energized conductors within which a shock hazard exists?
  • At what voltage level does trained or authorized personnel supervision become generally required for live work?
  • The amount of thermal energy impressed on a surface at a certain distance from the source of an electrical arc is known as the ?
  • Which feature is commonly used to identify a confined space?
  • After an incident, which practice most clearly supports safety improvement?
  • Which action best supports ongoing electrical safety improvement?
  • A PPE category is typically identified as an output of arc flash hazard analysis. Which option best reflects this output?
  • Which is the correct interpretation of insulation resistance testing during commissioning or maintenance?
  • Which substance may be present in fluorescent light fixtures?
  • Which statement best describes effective post-work verification after electrical work?
  • What is an important use of a hot stick?
  • How are grounding and bonding different in electrical safety?
  • Which statement best describes a GFCI’s reaction to a fault?
  • Which set of activities best supports continuous improvement in electrical safety performance?
  • How is energy source identification performed before work?
  • A shock of 5 mA can cause injury through which mechanism?
  • What causes arc flash and what makes it dangerous?
  • To approach closer than the Minimum Approach Distance, what is required?
  • Which practice is NOT part of maintaining arc flash PPE?
  • Is it recommended to use a compressor for an air test on high-voltage gloves because it provides more pressure and faster results?
  • In a lockout/tagout procedure, who installs lockout/tagout devices?
  • After completing installation or repair on electrical equipment, which should be verified before returning it to service?
  • Which tool is used to remove a temporary ground?
  • The presence of which chemical in fluorescent fixtures is a safety concern for electricians?
  • Under NFPA 70E, when is energized work permitted and what safeguards are required?
  • What PPE is typically required for arc flash protection?
  • What is the purpose of arc flash labeling on electrical equipment?
  • What is the primary purpose of insulation resistance testing (megger) in electrical safety?
  • During erection of scaffolding, which action should be performed on each part?
  • How does a permit-to-work system contribute to electrical safety?
  • How should a worker respond to an arc flash incident?
  • What is the difference between an arc flash label for equipment and its absence?
  • In some older fluorescent fixtures, which chemical might be present?
  • The base of a ladder should be about what fraction of the ladder's vertical height away from the wall?
  • Job-specific electrical safety procedures provide:
  • The NEC covers what?
  • The arc flash boundary (AFC) is the approach limit at which a person could receive a second-degree burn if an arc flash occurs. Which label is used for this boundary?
  • Class 0 rubber gloves are used when working with voltages less than __________.
  • What should be checked prior to using insulated tools near live parts?
  • What term describes a study used to assess a worker's potential exposure to arc flash energy?
  • Fall protection must be used when employees are on a walking or working surface that is _____ or more above a lower level and has an unprotected edge or side.
  • In lockout/tagout practices, what distinguishes a lock from a tag?
  • Which of the following is considered a confined space?
  • How should PPE be stored and maintained to ensure ongoing protection?
  • What is the primary purpose of NFPA 70E in electrical safety?
  • What actions should you take if PPE is discovered to be damaged during work?
  • How long should confined-space entry permits be retained?
  • For work at 1.0 meter elevation, is fall protection required?
  • Which hazards are listed as potential hazards in confined spaces?
  • Which statement best defines incident energy in arc flash safety?
  • How do you ensure proper grounding and bonding of electrical equipment?
  • What is the role of insulation-resistant testing (megger) in electrical safety?
  • Which practice is NOT recommended when electrical work is performed in damp or wet conditions?
  • Why is bonding important in electrical safety?
  • What is the primary purpose of insulation-resistant testing (megger) in electrical safety?
  • Which is the least effective method of preventing risk?
  • Older fluorescent fixtures have been known to contain which chemical?
  • What is the purpose of a voltage verification procedure before servicing electrical equipment?
  • List three core requirements of a Lockout/Tagout program as applied to electrical work.
  • What is the first critical step when performing Lockout/Tagout on equipment?
  • Who qualifies as a "qualified person" under NFPA 70E?
  • What is a key step in proper grounding and bonding of electrical equipment?
  • How should electrical work near water or moisture be conducted safely?
  • What are the main steps in a hazard analysis before electrical work?
  • A machine guard is an example of which type of control?
  • In lockout/tagout, what is the practical difference between applying a lock and applying a tag?
  • What best describes touch potential vs step potential hazard near outdoor HV sources?
  • How does the 'two-person rule' enhance safety for certain electrical tasks?
  • What considerations apply to using test leads and meters on live circuits?
  • What is the purpose of a job briefing or pre-task briefing for electrical work?
  • After maintenance, which testing step ensures safety devices function as intended?
  • Which term best describes the energy measure used in arc flash calculations to quantify thermal exposure?
  • A PFAS anchorage point for a 6' lanyard must be able to hold how many pounds?
  • Low-voltage conductors are responsible for most electrocution deaths due to which reason?
  • Asbestos may be found in facilities constructed before which year?
  • Which option is not a component of continuous improvement in electrical safety?
  • One who has demonstrated the skills and safety training to identify hazards in electrical work is known as a?
  • What information is conveyed by arc flash labels on electrical equipment?
  • Which description best fits the tool used to verify zero voltage at the work location?
  • After installation, which statement best reflects proper testing?
  • How is PPE category determined for arc flash?
  • What is the purpose of insulation continuity testing after installation or repair?
  • How do de-energized work and isolated work differ?
  • Which statement correctly differentiates preventative maintenance from corrective maintenance?
  • How should flame-resistant clothing be cleaned and maintained?
  • Which items are included in key pre-work equipment inspection steps?
  • Which of the following actions is NOT a recommended practice around live electrical equipment?
  • What is incident energy measured on an arc flash label used to determine?
  • Which statement best describes the relationship between energy source verification and task authorization?
  • Polychlorinated biphenyls (PCBs) are chemicals that may be found in which electrical equipment?
  • What is the main function of a lockout device in energy control procedures?
  • Before using insulated electrical tools, which action is essential to ensure safety?
  • When is a permit-required confined space relevant to electrical work, and what additional controls apply?
  • What should a clearance sign or barricade accomplish around live equipment?
  • What is the role of a GFCI in electrical safety?
  • What is the proper use of insulated tools near live parts?
  • What is the role of a supervisor in electrical safety?
  • What type of extinguisher is recommended for electrical fires?
  • What is the purpose of a permit for energized work?
  • The best way to protect yourself from solvent hazards is to?
  • Which energy categories are included in OSHA's lockout/tagout rule?
  • Which boundary, among the commonly defined safety boundaries, indicates the distance at which there is a potential shock hazard near exposed energized parts?
  • What steps should be taken to verify a circuit is de-energized before work?
  • How should arc flash PPE be selected and maintained?
  • What unit is used to express incident energy in arc flash calculations?
  • Which option correctly maps the six classes of rubber protective equipment to their class tags and voltage ratings?
  • Minimum and maximum scaffold plank overhang beyond end support is?
  • What is the purpose of the two-person rule in electrical safety?
  • What are boundary distances in the context of arc flash?
  • When is an energized work permit required?
  • When is a hot work permit required in electrical settings?
  • What is the purpose of temporary protective grounding?
  • What is incident energy in arc flash terms and why is it important for PPE selection?
  • Before determining the proper procedure for confined space entry, a(n) ____ must be performed.
  • Which practice helps maintain safety when working near overhead conductors?
  • Which statement best describes the purpose of arc flash boundaries?
  • How should an electrical fire be addressed, and what should you avoid using?
  • What are the recommended steps to safely extinguish an electrical fire?
  • Which device is designed to rapidly interrupt current when a ground fault is detected?
  • Which source should be consulted to determine the required PPE category for arc flash protection?
  • Which statement is a direct output of arc flash hazard analysis besides incident energy and PPE category?
  • Which combination of safety practices best reduces risk when working near electrical equipment?
  • What should be done if insulated tools are damaged?
  • Which combination provides full head and neck protection against arc flash?
  • What is the appropriate action when a panel shows signs of overheating (smell, discoloration)?
  • Which item is not a standard element of a Lockout/Tagout procedure?
  • What is the primary purpose of lockout/tagout procedures?
  • Which statement about arc flash boundaries is true?
  • Which practice is correct when lifting to prevent injury?
  • What is the proper use of a fire extinguisher on an electrical fire?
  • How should a worker protect themselves from arc flash when opening a panel?
  • What minimum approach distance governs safe entry near exposed energized parts, and how is it determined?
  • What is the difference between grounding and bonding in electrical safety?
  • Why should tool tips be kept away from live parts?
  • What is the role of PPE in electrical safety training?
  • Low-voltage conductors are responsible for most electrocution deaths because of which factor?
  • Which statement best describes the role of personal protective equipment in an electrical safety plan?
  • Define arc flash boundary and the two common approach boundaries used for worker protection.
  • Which item must be included on a lockout/tagout caution tag?
  • What is the primary role of a supervisor in ensuring permits and safety procedures are followed?
Subscribe

Get the latest from Examzify

You can unsubscribe at any time. Read our privacy policy